Puldi õpetamine autole.

Puldi õpetamine autole.

PostitusPostitas yxhunt » 27 Apr 2023, 21:49

Tere
Mure selles, et mul poss ostis 99a mazda 323-e. Kuid pult ei toimi. Vahetasime patarei ära aga ikka ei toimi. Arvan et auto on nö. puldi ära unustanud.... Oskab keegi aidata, kuidas autole pult uuesti selgeks õpetada?
yxhunt
 
Postitusi: 1
Liitunud: 27 Apr 2023, 21:40

Re: Puldi õpetamine autole.

PostitusPostitas maaks » 28 Apr 2023, 08:37

Internetist leidsin sellise õpetuse, äkki töötab :-)
------------------------
It does sound like it just needs to be re-paired to the car, there might/should be the instructions in your owners manual on how to do that.
This. The fob will have to be reprogrammed.

"Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks."
-------------------
Siin veel üks:
https://www.justanswer.com/uk-car/7jsf4 ... nlock.html
Hi you have to reprogram the key fob after replacing the battery ,
Here is how its done .

Remove key from ignition.
Close all doors.
Open driver side door and leave open.
Perform the following steps within 24 seconds.
a. Insert key in ignition.
b. Turn key to ON and OFF.
c. Repeat step b two more times.
d. Remove key.
e. Push driver door frame button three times (black rubber button located on driver door frame that tell the vehicle whether or not door is closed.)
5. Buzz sound, chime or doors will lock and unlock should be heard at this point signaling that the vehicle is now in
programming mode. If not, wait 40 seconds and return to step 4.

6. All transmitters need to be programmed at this time, including the old ones. Push any button on the transmitter
two times. A buzz sound, chime or doors locking and unlocking should be heard at this point signaling that the
vehicle has accepted the new transmitter code. If there is only one transmitter, repeat this step two more times
using the only transmitter. If there are two transmitters, repeat this step two more times using the second
transmitter.

7. Push driver door frame button one time. Two buzz sounds, chimes or doors locking and unlocking 2 times should
Kasutaja avatar
maaks
 
Postitusi: 536
Liitunud: 16 Nov 2005, 18:53
Asukoht: Tallinn

Re: Puldi õpetamine autole.

PostitusPostitas Mario » 30 Apr 2023, 20:39

kui see on 1999.a mudel, millel on 2 nupuga pult (hele ja tume), siis:
The procedure of Program 8C Key for Mazda 323

1.Lock all doors of Mazda 323, plug key into ignition—>pull key out–>plug key into ignition again–>pull key out again…repeat until the immobilizer light flash.Then leave the key into igniton,and do not turn on,the keep the key in “OFF”position,and wait for 5 minutes.

2. The immo light flash frequency form fast to slow,then immo light off.

3. Turn the key to “ON” position,immo light on (start counting).The light from “light” to “off”(blinks) for a password process.You need to count the blinks to get the immobilizer code.The first set of blinks will gvie the first digit of the immo code.

4. There will be a pause,when you get first digit of immo code,the light will off.Turn the key off,then turn key on again.It will restart to flash,count blinks to get second digit of immo code…and so on.

5 The immo code is 8 digit code.When it complete,the immo light on,wait 3 seconds to turn key to “ON” position,wait immo light off.

Tol ajal meie regioonis läbi Esma Auto või Vilojeti müüdud autod on kõik ilma puldita ja paigaldati kohalikult Gemel Serpistar, Cobra või GT alarm, millel keskluku juhtimine. Vähe on neid, millel originaalne 2 puldiga kesklukk, sest tollased liisingutingimused nõudsid alarmi olemasolu ja tehas seda ei pakkunud.
If you can't fix it with a hammer... Then you've got an electrical problem!!
Kasutaja avatar
Mario
 
Postitusi: 6044
Liitunud: 29 Mär 2006, 17:37
Asukoht: Tartu-Jõgeva /55 608 255


Mine 323/MX-3/3/MX-5

Kes on foorumil

Kasutajad foorumit lugemas: Registreeritud kasutajaid pole ja 1 külaline

cron